/* * Copyright 2019 NXP * All rights reserved. * * SPDX-License-Identifier: BSD-3-Clause */ /*********************************************************************************************************************** * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. **********************************************************************************************************************/ /* clang-format off */ /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* !!GlobalInfo product: Pins v6.0 processor: K32L2B11xxxxA package_id: K32L2B11VLH0A mcu_data: ksdk2_0 processor_version: 0.0.0 board: FRDM-K32L2B pin_labels: - {pin_num: '23', pin_signal: PTA1/LPUART0_RX/TPM2_CH0, label: 'J1[2]/D0/UART0_RX', identifier: DEBUG_UART0_RX} - {pin_num: '24', pin_signal: PTA2/LPUART0_TX/TPM2_CH1, label: 'J1[4]/D1/UART0_TX', identifier: DEBUG_UART0_TX} - {pin_num: '60', pin_signal: LCD_P43/PTD3/SPI0_MISO/UART2_TX/TPM0_CH3/SPI0_MOSI/FXIO0_D3, label: 'J1[6]/D2/LCD_P43', identifier: LCD_P43} - {pin_num: '28', pin_signal: PTA12/TPM1_CH0, label: 'J1[8]/D3'} - {pin_num: '26', pin_signal: PTA4/I2C1_SDA/TPM0_CH1/NMI_b, label: 'J1[10]/D4/SW1', identifier: SW1} - {pin_num: '27', pin_signal: PTA5/USB_CLKIN/TPM0_CH2, label: 'J1[12]/D5/USB_CLKIN', identifier: USB0_CLKIN} - {pin_num: '17', pin_signal: CMP0_IN5/ADC0_SE4b/PTE29/TPM0_CH2/TPM_CLKIN0, label: 'J1[14]/D6/CMP0_IN5'} - {pin_num: '18', pin_signal: DAC0_OUT/ADC0_SE23/CMP0_IN4/PTE30/TPM0_CH3/TPM_CLKIN1/LPUART1_TX/LPTMR0_ALT1, label: 'J1[16]/J4[11]/D7/CMP0_IN4/DAC_OUT'} - {pin_num: '29', pin_signal: PTA13/TPM1_CH1, label: 'J2[2]/D8'} - {pin_num: '59', pin_signal: LCD_P42/PTD2/SPI0_MOSI/UART2_RX/TPM0_CH2/SPI0_MISO/FXIO0_D2, label: 'J2[4]/D9/LCD_P42', identifier: LCD_P42} - {pin_num: '61', pin_signal: LCD_P44/PTD4/LLWU_P14/SPI1_SS/UART2_RX/TPM0_CH4/FXIO0_D4, label: 'J2[6]/D10/SPI1_PCS0/LCD_P44', identifier: LCD_P44} - {pin_num: '63', pin_signal: LCD_P46/ADC0_SE7b/PTD6/LLWU_P15/SPI1_MOSI/LPUART0_RX/SPI1_MISO/FXIO0_D6, label: 'J2[8]/D11/SPI1_MOSI/LCD_P46'} - {pin_num: '64', pin_signal: LCD_P47/PTD7/SPI1_MISO/LPUART0_TX/SPI1_MOSI/FXIO0_D7, label: 'J2[10]/D12/SPI1_MISO/LCD_P47'} - {pin_num: '62', pin_signal: LCD_P45/ADC0_SE6b/PTD5/SPI1_SCK/UART2_TX/TPM0_CH5/FXIO0_D5, label: 'J2[12]/D13/SPI1_SCK/LED1/LCD_P45', identifier: LED1} - {pin_num: '1', pin_signal: LCD_P48/PTE0/CLKOUT32K/SPI1_MISO/LPUART1_TX/RTC_CLKOUT/CMP0_OUT/I2C1_SDA, label: 'J2[18]/J4[9]/D14/I2C1_SDA/CMP0_OUT/LCD_P48', identifier: I2C1_SDA} - {pin_num: '2', pin_signal: LCD_P49/PTE1/SPI1_MOSI/LPUART1_RX/SPI1_MISO/I2C1_SCL, label: 'J2[20]/D15/I2C1_SCL/LCD_P49', identifier: I2C1_SCL} - {pin_num: '39', pin_signal: LCD_P12/PTB16/SPI1_MOSI/LPUART0_RX/TPM_CLKIN0/SPI1_MISO, label: 'J2[19]/LCD_P12'} - {pin_num: '40', pin_signal: LCD_P13/PTB17/SPI1_MISO/LPUART0_TX/TPM_CLKIN1/SPI1_MOSI, label: 'J2[17]/LCD_P13'} - {pin_num: '54', pin_signal: LCD_P25/PTC5/LLWU_P9/SPI0_SCK/LPTMR0_ALT2/CMP0_OUT, label: 'J1[15]/INT1_ACCEL/LCD_P25', identifier: INT1_ACCEL} - {pin_num: '56', pin_signal: LCD_P27/CMP0_IN1/PTC7/SPI0_MISO/USB_SOF_OUT/SPI0_MOSI, label: 'J1[11]/USB_SOF_OUT/LCD_P27', identifier: LCD_P27} - {pin_num: '55', pin_signal: LCD_P26/CMP0_IN0/PTC6/LLWU_P10/SPI0_MOSI/EXTRG_IN/SPI0_MISO, label: 'J1[9]/LCD_P26', identifier: LCD_P26} - {pin_num: '53', pin_signal: LCD_P24/PTC4/LLWU_P8/SPI0_SS/LPUART1_TX/TPM0_CH3, label: 'J1[7]/LCD_P24', identifier: LCD_P24} - {pin_num: '43', pin_signal: LCD_P20/ADC0_SE14/PTC0/EXTRG_IN/USB_SOF_OUT/CMP0_OUT, label: 'J1[5]/LCD_P20/USB_SOF_OUT', identifier: LCD_P20;USB_SOF_OUT} - {pin_num: '42', pin_signal: LCD_P15/PTB19/TPM2_CH1, label: 'J1[3]/LCD_P15', identifier: LCD_P15} - {pin_num: '41', pin_signal: LCD_P14/PTB18/TPM2_CH0, label: 'J1[1]/LCD_P14', identifier: LCD_P14} - {pin_num: '12', pin_signal: ADC0_DM3/ADC0_SE7a/PTE23/TPM2_CH1/UART2_RX/FXIO0_D7, label: 'J4[7]/DIFF_ADC1_DM'} - {pin_num: '11', pin_signal: ADC0_DP3/ADC0_SE3/PTE22/TPM2_CH0/UART2_TX/FXIO0_D6, label: 'J4[5]/DIFF_ADC1_DP'} - {pin_num: '10', pin_signal: LCD_P60/ADC0_DM0/ADC0_SE4a/PTE21/TPM1_CH1/LPUART0_RX/FXIO0_D5, label: 'J4[3]/DIFF_ADC0_DM/LCD_P60', identifier: LCD_P60} - {pin_num: '9', pin_signal: LCD_P59/ADC0_DP0/ADC0_SE0/PTE20/TPM1_CH0/LPUART0_TX/FXIO0_D4, label: 'J4[1]/DIFF_ADC0_DP/LCD_P59', identifier: LCD_P59} - {pin_num: '35', pin_signal: LCD_P0/ADC0_SE8/PTB0/LLWU_P5/I2C0_SCL/TPM1_CH0, label: 'J4[2]/A0/LCD_P0'} - {pin_num: '36', pin_signal: LCD_P1/ADC0_SE9/PTB1/I2C0_SDA/TPM1_CH1, label: 'J4[4]/A1/LCD_P1'} - {pin_num: '37', pin_signal: LCD_P2/ADC0_SE12/PTB2/I2C0_SCL/TPM2_CH0, label: 'J4[6]/A2/LCD_P2'} - {pin_num: '38', pin_signal: LCD_P3/ADC0_SE13/PTB3/I2C0_SDA/TPM2_CH1, label: 'J4[8]/A3/LCD_P3'} - {pin_num: '45', pin_signal: LCD_P22/ADC0_SE11/PTC2/I2C1_SDA/TPM0_CH1, label: 'J4[10]/A4/LCD_P22'} - {pin_num: '44', pin_signal: LCD_P21/ADC0_SE15/PTC1/LLWU_P6/RTC_CLKIN/I2C1_SCL/TPM0_CH0, label: 'J4[12]/A5/LCD_P21'} - {pin_num: '5', pin_signal: USB0_DP, label: 'J10[3]/USB_DP', identifier: USB0_DP} - {pin_num: '6', pin_signal: USB0_DM, label: 'J10[2]/USB_DM', identifier: USB0_DM} - {pin_num: '22', pin_signal: PTA0/TPM0_CH5/SWD_CLK, label: 'J11[4]/K32L2_SWD_CLK'} - {pin_num: '25', pin_signal: PTA3/I2C1_SCL/TPM0_CH0/SWD_DIO, label: 'J11[2]/SWD_DIO_TGTMCU'} - {pin_num: '32', pin_signal: EXTAL0/PTA18/LPUART1_RX/TPM_CLKIN0, label: EXTAL_32KHZ, identifier: EXTAL_32KHZ} - {pin_num: '33', pin_signal: XTAL0/PTA19/LPUART1_TX/TPM_CLKIN1/LPTMR0_ALT1, label: XTAL_32KHZ, identifier: XTAL_32KHZ} - {pin_num: '34', pin_signal: PTA20/RESET_b, label: 'J11[10]/J3[6]/RESET/SW2'} - {pin_num: '46', pin_signal: LCD_P23/PTC3/LLWU_P7/SPI1_SCK/LPUART1_RX/TPM0_CH2/CLKOUT, label: SW3/LLWU_P7/LCD_P23, identifier: SW3} - {pin_num: '58', pin_signal: LCD_P41/ADC0_SE5b/PTD1/SPI0_SCK/TPM0_CH1/FXIO0_D1, label: 'U2[9]/U10[9]/INT2_ACCEL/INT1_MAG/LCD_P41', identifier: INT2_ACCEL;INT1_MAG} - {pin_num: '21', pin_signal: PTE25/TPM0_CH1/I2C0_SDA, label: 'U2[6]/U10[6]/I2C0_SDA', identifier: I2C0_SDA} - {pin_num: '20', pin_signal: PTE24/TPM0_CH0/I2C0_SCL, label: 'U2[7]/U10[4]/I2C0_SCL', identifier: I2C0_SCL} - {pin_num: '3', pin_signal: VDD17, label: P3V3_K32L2B} - {pin_num: '13', pin_signal: VDDA, label: P3V3_K32L2B} - {pin_num: '30', pin_signal: VDD94, label: P3V3_K32L2B} - {pin_num: '4', pin_signal: VSS18, label: GND} - {pin_num: '16', pin_signal: VSSA, label: GND} - {pin_num: '31', pin_signal: VSS95, label: GND} - {pin_num: '47', pin_signal: VSS136, label: GND} - {pin_num: '7', pin_signal: VOUT33, label: VOUT33} - {pin_num: '8', pin_signal: VREGIN, label: USB_REGIN, identifier: USB0_VREGIN} - {pin_num: '15', pin_signal: VREFL, label: GND} - {pin_num: '14', pin_signal: VREFH, label: 'J19[2]/P3V3_K32L2B'} - {pin_num: '19', pin_signal: PTE31/TPM0_CH4, label: LED2, identifier: LED2} - {pin_num: '48', pin_signal: VLL3, label: 'J12[1]/P3V3_K32L2B'} - {pin_num: '49', pin_signal: VLL2/LCD_P4/PTC20, label: TP12/LCD_P4} - {pin_num: '50', pin_signal: VLL1/LCD_P5/PTC21, label: TP10/LCD_P5} - {pin_num: '51', pin_signal: VCAP2/LCD_P6/PTC22, label: LCD_P6} - {pin_num: '52', pin_signal: VCAP1/LCD_P39/PTC23, label: LCD_P39} - {pin_num: '57', pin_signal: LCD_P40/PTD0/SPI0_SS/TPM0_CH0/FXIO0_D0, label: LCD-09_P40, identifier: LCD_P40} * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ /* clang-format on */ #include "fsl_common.h" #include "fsl_port.h" #include "fsl_gpio.h" #include "pin_mux.h" /* FUNCTION ************************************************************************************************************ * * Function Name : BOARD_InitBootPins * Description : Calls initialization functions. * * END ****************************************************************************************************************/ void BOARD_InitBootPins(void) { BOARD_InitPins(); BOARD_InitDEBUG_UARTPins(); } /* clang-format off */ /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* BOARD_InitPins: - options: {callFromInitBoot: 'true', prefix: BOARD_, coreID: core0, enableClock: 'true'} - pin_list: [] * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ /* clang-format on */ /* FUNCTION ************************************************************************************************************ * * Function Name : BOARD_InitPins * Description : Configures pin routing and optionally pin electrical features. * * END ****************************************************************************************************************/ void BOARD_InitPins(void) { } /* clang-format off */ /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* BOARD_InitLCDPins: - options: {prefix: BOARD_, coreID: core0, enableClock: 'true'} - pin_list: - {pin_num: '41', peripheral: LCD, signal: 'P, 14', pin_signal: LCD_P14/PTB18/TPM2_CH0, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '42', peripheral: LCD, signal: 'P, 15', pin_signal: LCD_P15/PTB19/TPM2_CH1, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '43', peripheral: LCD, signal: 'P, 20', pin_signal: LCD_P20/ADC0_SE14/PTC0/EXTRG_IN/USB_SOF_OUT/CMP0_OUT, identifier: LCD_P20, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '53', peripheral: LCD, signal: 'P, 24', pin_signal: LCD_P24/PTC4/LLWU_P8/SPI0_SS/LPUART1_TX/TPM0_CH3, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '55', peripheral: LCD, signal: 'P, 26', pin_signal: LCD_P26/CMP0_IN0/PTC6/LLWU_P10/SPI0_MOSI/EXTRG_IN/SPI0_MISO, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '56', peripheral: LCD, signal: 'P, 27', pin_signal: LCD_P27/CMP0_IN1/PTC7/SPI0_MISO/USB_SOF_OUT/SPI0_MOSI, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '57', peripheral: LCD, signal: 'P, 40', pin_signal: LCD_P40/PTD0/SPI0_SS/TPM0_CH0/FXIO0_D0, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '59', peripheral: LCD, signal: 'P, 42', pin_signal: LCD_P42/PTD2/SPI0_MOSI/UART2_RX/TPM0_CH2/SPI0_MISO/FXIO0_D2, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '60', peripheral: LCD, signal: 'P, 43', pin_signal: LCD_P43/PTD3/SPI0_MISO/UART2_TX/TPM0_CH3/SPI0_MOSI/FXIO0_D3, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '61', peripheral: LCD, signal: 'P, 44', pin_signal: LCD_P44/PTD4/LLWU_P14/SPI1_SS/UART2_RX/TPM0_CH4/FXIO0_D4, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '9', peripheral: LCD, signal: 'P, 59', pin_signal: LCD_P59/ADC0_DP0/ADC0_SE0/PTE20/TPM1_CH0/LPUART0_TX/FXIO0_D4, slew_rate: slow, pull_select: up, pull_enable: disable} - {pin_num: '10', peripheral: LCD, signal: 'P, 60', pin_signal: LCD_P60/ADC0_DM0/ADC0_SE4a/PTE21/TPM1_CH1/LPUART0_RX/FXIO0_D5, slew_rate: slow, pull_select: up, pull_enable: disable} * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ /* clang-format on */ /* FUNCTION ************************************************************************************************************ * * Function Name : BOARD_InitLCDPins * Description : Configures pin routing and optionally pin electrical features. * * END ****************************************************************************************************************/ void BOARD_InitLCDPins(void) { /* Port B Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortB); /* Port C Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortC); /* Port D Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortD); /* Port E Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortE); /* PORTB18 (pin 41) is configured as LCD_P14 */ PORT_SetPinMux(BOARD_LCD_P14_PORT, BOARD_LCD_P14_PIN, kPORT_PinDisabledOrAnalog); PORTB->PCR[18] = ((PORTB->PCR[18] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding * pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTB19 (pin 42) is configured as LCD_P15 */ PORT_SetPinMux(BOARD_LCD_P15_PORT, BOARD_LCD_P15_PIN, kPORT_PinDisabledOrAnalog); PORTB->PCR[19] = ((PORTB->PCR[19] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding * pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTC0 (pin 43) is configured as LCD_P20 */ PORT_SetPinMux(BOARD_LCD_P20_PORT, BOARD_LCD_P20_PIN, kPORT_PinDisabledOrAnalog); PORTC->PCR[0] = ((PORTC->PCR[0] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTC4 (pin 53) is configured as LCD_P24 */ PORT_SetPinMux(BOARD_LCD_P24_PORT, BOARD_LCD_P24_PIN, kPORT_PinDisabledOrAnalog); PORTC->PCR[4] = ((PORTC->PCR[4] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTC6 (pin 55) is configured as LCD_P26 */ PORT_SetPinMux(BOARD_LCD_P26_PORT, BOARD_LCD_P26_PIN, kPORT_PinDisabledOrAnalog); PORTC->PCR[6] = ((PORTC->PCR[6] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTC7 (pin 56) is configured as LCD_P27 */ PORT_SetPinMux(BOARD_LCD_P27_PORT, BOARD_LCD_P27_PIN, kPORT_PinDisabledOrAnalog); PORTC->PCR[7] = ((PORTC->PCR[7] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTD0 (pin 57) is configured as LCD_P40 */ PORT_SetPinMux(BOARD_LCD_P40_PORT, BOARD_LCD_P40_PIN, kPORT_PinDisabledOrAnalog); PORTD->PCR[0] = ((PORTD->PCR[0] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTD2 (pin 59) is configured as LCD_P42 */ PORT_SetPinMux(BOARD_LCD_P42_PORT, BOARD_LCD_P42_PIN, kPORT_PinDisabledOrAnalog); PORTD->PCR[2] = ((PORTD->PCR[2] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTD3 (pin 60) is configured as LCD_P43 */ PORT_SetPinMux(BOARD_LCD_P43_PORT, BOARD_LCD_P43_PIN, kPORT_PinDisabledOrAnalog); PORTD->PCR[3] = ((PORTD->PCR[3] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTD4 (pin 61) is configured as LCD_P44 */ PORT_SetPinMux(BOARD_LCD_P44_PORT, BOARD_LCD_P44_PIN, kPORT_PinDisabledOrAnalog); PORTD->PCR[4] = ((PORTD->PCR[4] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTE20 (pin 9) is configured as LCD_P59 */ PORT_SetPinMux(BOARD_LCD_P59_PORT, BOARD_LCD_P59_PIN, kPORT_PinDisabledOrAnalog); PORTE->PCR[20] = ((PORTE->PCR[20] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding * pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); /* PORTE21 (pin 10) is configured as LCD_P60 */ PORT_SetPinMux(BOARD_LCD_P60_PORT, BOARD_LCD_P60_PIN, kPORT_PinDisabledOrAnalog); PORTE->PCR[21] = ((PORTE->PCR[21] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding * pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_SlowSlewRate)); } /* clang-format off */ /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* BOARD_InitBUTTONSPins: - options: {prefix: BOARD_, coreID: core0, enableClock: 'true'} - pin_list: - {pin_num: '26', peripheral: GPIOA, signal: 'GPIO, 4', pin_signal: PTA4/I2C1_SDA/TPM0_CH1/NMI_b, direction: INPUT, slew_rate: fast, pull_select: up, pull_enable: enable, passive_filter: disable} - {pin_num: '46', peripheral: GPIOC, signal: 'GPIO, 3', pin_signal: LCD_P23/PTC3/LLWU_P7/SPI1_SCK/LPUART1_RX/TPM0_CH2/CLKOUT, direction: INPUT, slew_rate: fast, pull_select: up, pull_enable: enable} * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ /* clang-format on */ /* FUNCTION ************************************************************************************************************ * * Function Name : BOARD_InitBUTTONSPins * Description : Configures pin routing and optionally pin electrical features. * * END ****************************************************************************************************************/ void BOARD_InitBUTTONSPins(void) { /* Port A Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortA); /* Port C Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortC); gpio_pin_config_t SW1_config = { .pinDirection = kGPIO_DigitalInput, .outputLogic = 0U }; /* Initialize GPIO functionality on pin PTA4 (pin 26) */ GPIO_PinInit(BOARD_SW1_GPIO, BOARD_SW1_PIN, &SW1_config); gpio_pin_config_t SW3_config = { .pinDirection = kGPIO_DigitalInput, .outputLogic = 0U }; /* Initialize GPIO functionality on pin PTC3 (pin 46) */ GPIO_PinInit(BOARD_SW3_GPIO, BOARD_SW3_PIN, &SW3_config); const port_pin_config_t SW1 = {/* Internal pull-up resistor is enabled */ kPORT_PullUp, /* Fast slew rate is configured */ kPORT_FastSlewRate, /* Passive filter is disabled */ kPORT_PassiveFilterDisable, /* Low drive strength is configured */ kPORT_LowDriveStrength, /* Pin is configured as PTA4 */ kPORT_MuxAsGpio}; /* PORTA4 (pin 26) is configured as PTA4 */ PORT_SetPinConfig(BOARD_SW1_PORT, BOARD_SW1_PIN, &SW1); const port_pin_config_t SW3 = {/* Internal pull-up resistor is enabled */ kPORT_PullUp, /* Fast slew rate is configured */ kPORT_FastSlewRate, /* Passive filter is disabled */ kPORT_PassiveFilterDisable, /* Low drive strength is configured */ kPORT_LowDriveStrength, /* Pin is configured as PTC3 */ kPORT_MuxAsGpio}; /* PORTC3 (pin 46) is configured as PTC3 */ PORT_SetPinConfig(BOARD_SW3_PORT, BOARD_SW3_PIN, &SW3); } /* clang-format off */ /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* BOARD_InitLEDsPins: - options: {prefix: BOARD_, coreID: core0, enableClock: 'true'} - pin_list: - {pin_num: '19', peripheral: GPIOE, signal: 'GPIO, 31', pin_signal: PTE31/TPM0_CH4, direction: OUTPUT, gpio_init_state: 'true', slew_rate: slow, pull_select: down, pull_enable: disable} - {pin_num: '62', peripheral: GPIOD, signal: 'GPIO, 5', pin_signal: LCD_P45/ADC0_SE6b/PTD5/SPI1_SCK/UART2_TX/TPM0_CH5/FXIO0_D5, direction: OUTPUT, gpio_init_state: 'true', slew_rate: slow, pull_select: down, pull_enable: disable} * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ /* clang-format on */ /* FUNCTION ************************************************************************************************************ * * Function Name : BOARD_InitLEDsPins * Description : Configures pin routing and optionally pin electrical features. * * END ****************************************************************************************************************/ void BOARD_InitLEDsPins(void) { /* Port D Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortD); /* Port E Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortE); gpio_pin_config_t LED1_config = { .pinDirection = kGPIO_DigitalOutput, .outputLogic = 1U }; /* Initialize GPIO functionality on pin PTD5 (pin 62) */ GPIO_PinInit(BOARD_LED1_GPIO, BOARD_LED1_PIN, &LED1_config); gpio_pin_config_t LED2_config = { .pinDirection = kGPIO_DigitalOutput, .outputLogic = 1U }; /* Initialize GPIO functionality on pin PTE31 (pin 19) */ GPIO_PinInit(BOARD_LED2_GPIO, BOARD_LED2_PIN, &LED2_config); const port_pin_config_t LED1 = {/* Internal pull-up/down resistor is disabled */ kPORT_PullDisable, /* Slow slew rate is configured */ kPORT_SlowSlewRate, /* Passive filter is disabled */ kPORT_PassiveFilterDisable, /* Low drive strength is configured */ kPORT_LowDriveStrength, /* Pin is configured as PTD5 */ kPORT_MuxAsGpio}; /* PORTD5 (pin 62) is configured as PTD5 */ PORT_SetPinConfig(BOARD_LED1_PORT, BOARD_LED1_PIN, &LED1); const port_pin_config_t LED2 = {/* Internal pull-up/down resistor is disabled */ kPORT_PullDisable, /* Slow slew rate is configured */ kPORT_SlowSlewRate, /* Passive filter is disabled */ kPORT_PassiveFilterDisable, /* Low drive strength is configured */ kPORT_LowDriveStrength, /* Pin is configured as PTE31 */ kPORT_MuxAsGpio}; /* PORTE31 (pin 19) is configured as PTE31 */ PORT_SetPinConfig(BOARD_LED2_PORT, BOARD_LED2_PIN, &LED2); } /* clang-format off */ /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* BOARD_InitDEBUG_UARTPins: - options: {callFromInitBoot: 'true', prefix: BOARD_, coreID: core0, enableClock: 'true'} - pin_list: - {pin_num: '23', peripheral: LPUART0, signal: RX, pin_signal: PTA1/LPUART0_RX/TPM2_CH0, slew_rate: fast, pull_select: down, pull_enable: disable} - {pin_num: '24', peripheral: LPUART0, signal: TX, pin_signal: PTA2/LPUART0_TX/TPM2_CH1, direction: OUTPUT, slew_rate: fast, pull_select: down, pull_enable: disable} * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ /* clang-format on */ /* FUNCTION ************************************************************************************************************ * * Function Name : BOARD_InitDEBUG_UARTPins * Description : Configures pin routing and optionally pin electrical features. * * END ****************************************************************************************************************/ void BOARD_InitDEBUG_UARTPins(void) { /* Port A Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortA); const port_pin_config_t DEBUG_UART0_RX = {/* Internal pull-up/down resistor is disabled */ kPORT_PullDisable, /* Fast slew rate is configured */ kPORT_FastSlewRate, /* Passive filter is disabled */ kPORT_PassiveFilterDisable, /* Low drive strength is configured */ kPORT_LowDriveStrength, /* Pin is configured as LPUART0_RX */ kPORT_MuxAlt2}; /* PORTA1 (pin 23) is configured as LPUART0_RX */ PORT_SetPinConfig(BOARD_DEBUG_UART0_RX_PORT, BOARD_DEBUG_UART0_RX_PIN, &DEBUG_UART0_RX); const port_pin_config_t DEBUG_UART0_TX = {/* Internal pull-up/down resistor is disabled */ kPORT_PullDisable, /* Fast slew rate is configured */ kPORT_FastSlewRate, /* Passive filter is disabled */ kPORT_PassiveFilterDisable, /* Low drive strength is configured */ kPORT_LowDriveStrength, /* Pin is configured as LPUART0_TX */ kPORT_MuxAlt2}; /* PORTA2 (pin 24) is configured as LPUART0_TX */ PORT_SetPinConfig(BOARD_DEBUG_UART0_TX_PORT, BOARD_DEBUG_UART0_TX_PIN, &DEBUG_UART0_TX); SIM->SOPT5 = ((SIM->SOPT5 & /* Mask bits to zero which are setting */ (~(SIM_SOPT5_LPUART0TXSRC_MASK | SIM_SOPT5_LPUART0RXSRC_MASK))) /* LPUART0 Transmit Data Source Select: LPUART0_TX pin. */ | SIM_SOPT5_LPUART0TXSRC(SOPT5_LPUART0TXSRC_LPUART_TX) /* LPUART0 Receive Data Source Select: LPUART_RX pin. */ | SIM_SOPT5_LPUART0RXSRC(SOPT5_LPUART0RXSRC_LPUART_RX)); } /* clang-format off */ /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* BOARD_InitUSBPins: - options: {prefix: BOARD_, coreID: core0, enableClock: 'true'} - pin_list: - {pin_num: '5', peripheral: USB0, signal: DP, pin_signal: USB0_DP} - {pin_num: '6', peripheral: USB0, signal: DM, pin_signal: USB0_DM} - {pin_num: '8', peripheral: USB0, signal: VREGIN, pin_signal: VREGIN} - {pin_num: '43', peripheral: USB0, signal: SOF_OUT, pin_signal: LCD_P20/ADC0_SE14/PTC0/EXTRG_IN/USB_SOF_OUT/CMP0_OUT, identifier: USB_SOF_OUT, slew_rate: fast, pull_select: up, pull_enable: disable} - {pin_num: '27', peripheral: USB0, signal: CLKIN, pin_signal: PTA5/USB_CLKIN/TPM0_CH2, slew_rate: fast, pull_select: up, pull_enable: disable} * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ /* clang-format on */ /* FUNCTION ************************************************************************************************************ * * Function Name : BOARD_InitUSBPins * Description : Configures pin routing and optionally pin electrical features. * * END ****************************************************************************************************************/ void BOARD_InitUSBPins(void) { /* Port A Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortA); /* Port C Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortC); /* PORTA5 (pin 27) is configured as USB_CLKIN */ PORT_SetPinMux(BOARD_USB0_CLKIN_PORT, BOARD_USB0_CLKIN_PIN, kPORT_MuxAlt2); PORTA->PCR[5] = ((PORTA->PCR[5] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Fast slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_FastSlewRate)); /* PORTC0 (pin 43) is configured as USB_SOF_OUT */ PORT_SetPinMux(BOARD_USB_SOF_OUT_PORT, BOARD_USB_SOF_OUT_PIN, kPORT_MuxAlt4); PORTC->PCR[0] = ((PORTC->PCR[0] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Fast slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_FastSlewRate)); } /* clang-format off */ /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* BOARD_InitACCEL_I2CPins: - options: {prefix: BOARD_, coreID: core0, enableClock: 'true'} - pin_list: - {pin_num: '20', peripheral: I2C0, signal: SCL, pin_signal: PTE24/TPM0_CH0/I2C0_SCL, slew_rate: fast, pull_select: up, pull_enable: enable} - {pin_num: '21', peripheral: I2C0, signal: SDA, pin_signal: PTE25/TPM0_CH1/I2C0_SDA, slew_rate: fast, pull_select: up, pull_enable: enable} - {pin_num: '58', peripheral: GPIOD, signal: 'GPIO, 1', pin_signal: LCD_P41/ADC0_SE5b/PTD1/SPI0_SCK/TPM0_CH1/FXIO0_D1, identifier: INT2_ACCEL, direction: INPUT, slew_rate: fast, pull_select: up, pull_enable: disable} - {pin_num: '54', peripheral: GPIOC, signal: 'GPIO, 5', pin_signal: LCD_P25/PTC5/LLWU_P9/SPI0_SCK/LPTMR0_ALT2/CMP0_OUT, direction: INPUT, slew_rate: fast, pull_select: up, pull_enable: disable} * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ /* clang-format on */ /* FUNCTION ************************************************************************************************************ * * Function Name : BOARD_InitACCEL_I2CPins * Description : Configures pin routing and optionally pin electrical features. * * END ****************************************************************************************************************/ void BOARD_InitACCEL_I2CPins(void) { /* Port C Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortC); /* Port D Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortD); /* Port E Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortE); gpio_pin_config_t INT1_ACCEL_config = { .pinDirection = kGPIO_DigitalInput, .outputLogic = 0U }; /* Initialize GPIO functionality on pin PTC5 (pin 54) */ GPIO_PinInit(BOARD_INT1_ACCEL_GPIO, BOARD_INT1_ACCEL_PIN, &INT1_ACCEL_config); gpio_pin_config_t INT2_ACCEL_config = { .pinDirection = kGPIO_DigitalInput, .outputLogic = 0U }; /* Initialize GPIO functionality on pin PTD1 (pin 58) */ GPIO_PinInit(BOARD_INT2_ACCEL_GPIO, BOARD_INT2_ACCEL_PIN, &INT2_ACCEL_config); /* PORTC5 (pin 54) is configured as PTC5 */ PORT_SetPinMux(BOARD_INT1_ACCEL_PORT, BOARD_INT1_ACCEL_PIN, kPORT_MuxAsGpio); PORTC->PCR[5] = ((PORTC->PCR[5] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Fast slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_FastSlewRate)); /* PORTD1 (pin 58) is configured as PTD1 */ PORT_SetPinMux(BOARD_INT2_ACCEL_PORT, BOARD_INT2_ACCEL_PIN, kPORT_MuxAsGpio); PORTD->PCR[1] = ((PORTD->PCR[1] & /* Mask bits to zero which are setting */ (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK))) /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the * corresponding PE field is set. */ | PORT_PCR_PS(kPORT_PullUp) /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */ | PORT_PCR_PE(kPORT_PullDisable) /* Slew Rate Enable: Fast slew rate is configured on the corresponding pin, if the pin is * configured as a digital output. */ | PORT_PCR_SRE(kPORT_FastSlewRate)); const port_pin_config_t I2C0_SCL = {/* Internal pull-up resistor is enabled */ kPORT_PullUp, /* Fast slew rate is configured */ kPORT_FastSlewRate, /* Passive filter is disabled */ kPORT_PassiveFilterDisable, /* Low drive strength is configured */ kPORT_LowDriveStrength, /* Pin is configured as I2C0_SCL */ kPORT_MuxAlt5}; /* PORTE24 (pin 20) is configured as I2C0_SCL */ PORT_SetPinConfig(BOARD_I2C0_SCL_PORT, BOARD_I2C0_SCL_PIN, &I2C0_SCL); const port_pin_config_t I2C0_SDA = {/* Internal pull-up resistor is enabled */ kPORT_PullUp, /* Fast slew rate is configured */ kPORT_FastSlewRate, /* Passive filter is disabled */ kPORT_PassiveFilterDisable, /* Low drive strength is configured */ kPORT_LowDriveStrength, /* Pin is configured as I2C0_SDA */ kPORT_MuxAlt5}; /* PORTE25 (pin 21) is configured as I2C0_SDA */ PORT_SetPinConfig(BOARD_I2C0_SDA_PORT, BOARD_I2C0_SDA_PIN, &I2C0_SDA); } /* clang-format off */ /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* BOARD_InitOSCPins: - options: {prefix: BOARD_, coreID: core0, enableClock: 'true'} - pin_list: - {pin_num: '32', peripheral: OSC0, signal: EXTAL0, pin_signal: EXTAL0/PTA18/LPUART1_RX/TPM_CLKIN0, slew_rate: no_init, pull_select: no_init, pull_enable: no_init} - {pin_num: '33', peripheral: OSC0, signal: XTAL0, pin_signal: XTAL0/PTA19/LPUART1_TX/TPM_CLKIN1/LPTMR0_ALT1, slew_rate: no_init, pull_select: no_init, pull_enable: no_init} * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ /* clang-format on */ /* FUNCTION ************************************************************************************************************ * * Function Name : BOARD_InitOSCPins * Description : Configures pin routing and optionally pin electrical features. * * END ****************************************************************************************************************/ void BOARD_InitOSCPins(void) { /* Port A Clock Gate Control: Clock enabled */ CLOCK_EnableClock(kCLOCK_PortA); /* PORTA18 (pin 32) is configured as EXTAL0 */ PORT_SetPinMux(BOARD_EXTAL_32KHZ_PORT, BOARD_EXTAL_32KHZ_PIN, kPORT_PinDisabledOrAnalog); /* PORTA19 (pin 33) is configured as XTAL0 */ PORT_SetPinMux(BOARD_XTAL_32KHZ_PORT, BOARD_XTAL_32KHZ_PIN, kPORT_PinDisabledOrAnalog); } /*********************************************************************************************************************** * EOF **********************************************************************************************************************/